What Is a Terp Slurper?
A terp slurper is a specialized quartz banger designed for low‑temperature dabbing. Unlike standard bangers where concentrate pools in one spot, a slurper uses a two‑stage system: concentrate melts in a lower reservoir, then gets pulled up through vertical or horizontal slots into an upper chamber where it finishes vaporizing. This continuous movement prevents scorching and maximizes flavor.
Most slurpers work with a terp pillar (or pearl) and a marble carb cap. The marble seals the top, creating a vacuum that forces air through bottom slits, spinning the pillar and spreading concentrate across hot quartz walls.
Lowrider Terp Slurper
The Lowrider features a descended 45‑degree angled neck that brings the hot banger closer to the table surface, lowering the rig's center of gravity and reducing joint strain. It combines a full‑weld seamless construction for maximum durability and airtight draw with a Control Tower vertical runway that forces concentrates upward, creating a massive heat surface with zero oil waste.
Step‑by‑Step: How to Use a Lowrider Terp Slurper
- Insert the pillar and pearls – Place the quartz terp pillar and any terp pearls inside the bottom dish of the slurper.
- Insert into your dab rig – Fit the 14mm male joint securely into your rig's female joint.
- Heat evenly – Use a butane torch to heat the bottom dish and the entire bucket for 30–40 seconds until it glows evenly. Avoid heating the joint directly.
- Let it cool – Allow the banger to cool for 45–60 seconds (or until it reaches your desired temperature, typically 500–550°F).
- Place the marble cap – Set the matching ball carb cap on top of the slurper. This seals the chamber and creates the vacuum needed for proper function.
- Apply your concentrate – Using a dab tool, place your concentrate onto the hot bottom dish. The vacuum will pull air through the bottom slits, causing the pillar to spin and smear oil across the heated walls.
- Inhale – Draw slowly and steadily. The Lowrider's vertical runway stretches the oil into a micro‑thin layer against the hot quartz, yielding clean, dense clouds.
Slide Control Tower Slurper
The Slide Control Tower is an evolution of the classic slurper, featuring an integrated slide that allows you to place your dab directly into the slide for a controlled, continuous flow of concentrates onto the dab dish. It uses a taller chamber to guide pillar travel and manage larger amounts of concentrate. The slanted slots force air through the dish, creating a spinning action that enhances vaporization.
Step‑by‑Step: How to Use a Slide Control Tower Slurper
- Set up your accessories – Drop the terp pillar and any terp pearls into the bottom dish.
- Insert into your rig – Secure the banger into your rig's joint.
- Heat the banger – Torch evenly for about 30 seconds on all sides until it's up to temperature.
- Warm the slide – Give the integrated slide 5–10 seconds of heat so concentrates flow smoothly into the chamber.
- Let it cool – Allow the banger to cool for 30–45 seconds before loading.
- Load your concentrate – Place your dab directly into the slide. It will slowly flow down into the main chamber for instant vaporization. This design is especially great for larger dabs (0.2g and above).
- Cap and inhale – Place the marble carb cap on top. The slanted slots will force air through the dish, creating a spinning action that evenly distributes your dab.
Double Slider Control Tower Slurper
The Double Slider features two terp slide funnels connected to each side of the banger. This design allows you to drop dabs into either funnel – as they melt, the concentrate slurps into the bucket and vaporizes more efficiently. It's perfect for sharing sessions with friends or loading up monster globs without clogging. A long beaded pillar insert spins inside the chamber for even vaporization.
Step‑by‑Step: How to Use a Double Slider Control Tower Slurper
- Insert the pillar and pearls – Place the terp pillar and pearls inside the bottom chamber.
- Secure into your rig – Fit the male joint into your rig. Double sliders typically come in 14mm male 90° configurations.
- Heat evenly – Torch the bottom dish and both sides for 30–40 seconds until glowing evenly.
- Cool down – Wait 45–60 seconds for the optimal low‑temperature range (500–550°F).
- Load your concentrate – Drop your dab into one or both of the slide funnels. As the concentrate melts, it slurps into the bucket and vaporizes.
- Cap and inhale – Place the marble carb cap on top. The double design doubles the surface area, allowing you to hit both sides in one draw.
Cleaning & Maintenance (All Types)
Proper cleaning is essential to preserve your quartz's clarity and performance.
- Swab while warm – After each session, while the quartz is still warm (around 200°F, never when red hot), wipe the internal chamber thoroughly with a cotton swab dipped in 99% isopropyl alcohol.
- Deep soak – For a complete deep clean, submerge the cooled banger, pillar, and ball cap in an alcohol bath for 15 minutes, wipe away excess resin, and let dry.
- Avoid thermal shock – Never run cold water over a hot banger. Always let it cool to room temperature before cleaning.
- Prevent clouding – Burned residue and repeated overheating cause "devitrification" (cloudy quartz). Controlled heating and regular swabbing keep your quartz crystal clear.